Hey everyone, it’s Sam here, part of the team at our SC Rubber Oil Seal supply company – and today I wanna dive into a question I get all the time from people in the medical device space: can SC rubber oil seals actually be used in medical devices? SC Rubber Oil Seal

First off, let’s get one thing straight: I’ve spent 7 years working in rubber seals, and I’ve seen way too many folks assume all rubber seals are cut from the same cloth. That’s a huge mistake, especially when you’re dealing with medical gear where even the tiniest contaminant or material flaw can cause big problems. SC rubber oil seals, for those who don’t know, are a specific type of nitrile rubber (NBR) composite seal – “SC” actually stands for “superior compression set” – which means they hold their shape way longer than standard NBR seals, even under constant pressure or high temps.
Let’s start with the basics of medical device requirements, because that’s the make-or-break here. The FDA, ISO, and other global regulators don’t mess around when it comes to materials that touch patients (or even just move critical parts inside a device). Medical devices range from something as simple as a blood pressure monitor’s air pump to as complex as an implantable insulin pump or a surgical robot. All of these have moving parts, and those parts depend on seals to prevent leaks, keep out contaminants, and maintain pressure or fluid integrity.
Now, can SC rubber oil seals check those boxes? The short answer is: yes, in most cases – but only if you pick the right grade and test it for your specific use case. Let me walk you through why this makes sense, and where people usually run into questions.
First, material compliance. A lot of medical device engineers worry about leachables – small molecules that can seep out of rubber and into bodily fluids or the device’s internal pathways. Standard NBR seals often have plasticizers or processing agents that leach, which is a non-starter for medical use. But our SC rubber oil seals are formulated with medical-grade NBR compounds, right? We don’t cut corners on that. Our raw materials meet USP Class VI standards, ISO 10993 biocompatibility requirements, and they pass FDA 21 CFR Part 177.2600 – the exact regulation for rubber goods that come into contact with food, drugs, and biological materials. That’s a big deal. For example, I worked with a team that makes portable insulin pumps a couple years back; they switched from custom silicone seals to our SC seals because the silicone was too soft and would compress too much after a few months, leading to insulin leaks. The SC seals held their compression, and they passed all the biocompatibility tests because we didn’t use any leachable additives.
Next, performance. Medical devices don’t get to run in perfect, controlled factory conditions. Take a surgical robot, for instance – it’s used in operating rooms that swing from 60°F prep areas to 80°F operating rooms, it’s exposed to sterilization cycles (either autoclaving with high temp/pressure or chemical sterilants like ethylene oxide), and it’s constantly moving thousands of times a day. Standard seals would wear out or lose shape after a few hundred cycles. Our SC rubber oil seals have a Shore A hardness of 70-85, which is just right for dynamic applications – not too soft that they flatten out, not too hard that they wear on mating parts. Plus, our compression set is under 10% after 22 hours at 125°C, which is way better than the 20% threshold for most industrial seals. That means even after 10,000 cycles, the seal is still tight. One customer that makes portable dialysis machines told us their old seals would fail after 6 months because the compression set was too high, leading to fluid leaks in the pump. Since switching to our SC seals, they’ve gone 18 months without a single seal failure – that’s the kind of performance that matters when you’re dealing with a life-sustaining device.
But here’s the catch: SC rubber oil seals aren’t for every medical device. Let’s talk about the limitations, because I don’t wanna mislead anyone. For implantable devices, like pacemaker leads or artificial heart valves, we usually recommend silicone or polyurethane seals instead of SC rubber. Why? Because SC rubber, even medical-grade, isn’t as flexible over long-term implantation (years, not months) as silicone, and some studies have shown it can cause mild tissue irritation in prolonged contact. Also, if your device needs to handle extremely harsh chemicals – like lab equipment that uses strong acids or solvents – SC rubber might not hold up; we have a separate line of fluorocarbon (FKM) seals for that, but our SC line is built for oils, fuels, and mild chemicals, which covers a ton of medical devices.
Another thing to consider: manufacturing consistency. Medical devices need parts that are identical every single time, no exceptions. If one seal is 0.5mm too small, it won’t seal; if another has a tiny air bubble, it could leak during a procedure. Our SC rubber oil seals are made in a ISO 13485-certified facility – that’s the exact standard for medical device manufacturing – so every seal we produce has tight tolerances (usually ±0.02mm for dimension accuracy) and goes through 100% visual inspection before it leaves our warehouse. We even do in-house helium leak testing for all dynamic seals, which is how we catch those tiny air bubbles that would slip past a regular visual check. I’ve had customers come to us after going through 3 different seal suppliers who had inconsistent seals – they’d get a batch that worked, then a batch that leaked half the time. For us, that never happens because we control every step of the process, from compounding the rubber to packaging the final seals.
Wait, let’s also talk about sterilization compatibility, because that’s a huge part of medical device use. A lot of medical devices are single-use, but many reusable ones go through autoclaving (steam sterilization at 121°C for 15 minutes) or ethylene oxide (EtO) sterilization. Our SC rubber oil seals can handle both. We test each batch for EtO absorption – meaning how much sterilant the seal retains, because if it’s too much, it can leach into the device later. Our seals absorb less than 0.1% EtO, which is way below the FDA’s limit of 1% for medical devices. For autoclaving, we’ve tested our seals through 500 autoclave cycles and the compression set only went up 2% – that’s nothing. A friend of mine that makes reusable surgical tools told us their old seals would crack after 20 autoclave cycles, so they switched to our SC seals and now they go 100 cycles without any issues.
But let’s be real, I know there’s still skepticism out there. A lot of engineers think “rubber is rubber, so it’s not good enough for medical.” But the difference between a random rubber seal and a medical-grade SC rubber oil seal is all about the formulation and testing. I can give you an example: a couple months back, we had a customer making hand-held nebulizers – those are the ones kids use for asthma. They were using a standard industrial NBR seal, and they kept having issues where the seal would swell when it came into contact with saline solution, leading to a clog in the nebulizer. We worked with their team to adjust our SC rubber compound to be more resistant to saline, and within a month, their failure rate dropped from 8% to less than 1%. That’s the kind of tailored solution we do here – we don’t just sell a generic seal, we work with your team to test it under your exact operating conditions.
So where does that leave us? If you’re working on a non-implantable medical device – things like nebulizers, blood pressure monitors, portable infusion pumps, surgical tool pumps, lab equipment fluid lines – yes, SC rubber oil seals are a solid, reliable choice. They check all the regulatory boxes, they hold up to the demands of medical use, and they’re cost-effective too – way cheaper than custom silicone or PTFE seals for most applications, without sacrificing performance.
But if you’re working on an implantable device, or a device that handles extremely harsh chemicals that SC rubber can’t resist, then we can point you to the right alternative – we don’t push our SC seals where they don’t fit, because we wanna build long-term relationships, not one-off sales.
Now, I know a lot of you are probably thinking, “Okay, that sounds good, but how do I make sure this works for my specific device?” The best way is to send us a sample of your current seal or a spec sheet – like the size, the operating temps, the chemicals it’s exposed to, and how many cycles it needs to last – and we can provide a free test sample. We’ll even run a small-scale performance test for you, no strings attached.

If you’re an engineer, a procurement manager, or a device designer looking for a seal that’s reliable, compliant, and works for your medical gear, don’t guess – reach out to our team. We’ve helped dozens of medical device companies fix seal issues that were costing them time, money, and even patient safety. No runaround, no complicated forms – just give us your specs, and we’ll hook you up with a seal that fits exactly what you need.
Shock Absorbers References
ISO 10993-5: Biological evaluation of medical devices – Part 5: Tests for in vitro cytotoxicity
FDA 21 CFR Part 177.2600: Rubber articles intended for repeated use in contact with components of food
USP <87>: Biological reactivity tests in vitro
ISO 13485: Medical devices – Quality management systems – Requirements for regulatory purposes
ASTM D395: Standard test methods for compression set of rubber materials
Jinhua Haobo Sealing Technology Co., Ltd.
Address: No.89, Hucheng Street, Tangxi Town, Wucheng District, Jinhua City, Zhejiang Province
E-mail: 245149293@qq.com
WebSite: https://www.haoboseal.com/