Hey everyone, it’s Jake here—got my hands dirty with motorcycle stands for over a decade now, and honestly? The #1 question I get from both new riders and shop techs isn’t “how strong is your stand” or “does it fit my 2024 KTM”—it’s “when do I lube my stand, and what the hell works without gunking up my swingarm.” Motorcycle Stand

Full transparency: I’m the guy behind the motorcycle stand supply side of things, so I test every lube trick you’ll see here on hundreds of stands before I send them out. I’ve seen folks use WD-40 (bad), grease that’s too thick (worse), and even peanut butter (please don’t—my intern still finds crumbs in shop stands sometimes). Let’s break this down like we’re hanging out in the shop bay, no fancy jargon, just stuff that actually works for your stand.
First, let’s get one thing straight: a motorcycle stand isn’t just a random metal frame—it’s a load-bearing hinge, a pivot point, and (if you’ve got a center stand) a rod that slides in and out of its mounting bracket. Each part has different needs, and slapping the same lube on everything is a one-way ticket to a stand that sticks when you’re loading your $15k bike. I learned this the hard way last year when a shop tech hit me up saying their stands were “jamming mid-lift”—turns out he sprayed WD-40 on both the pivot hinge AND the stand’s rubber foot. The WD-40 ate a tiny bit of the rubber, making it slip on concrete, and the gunk mixed with dirt to clog the hinge. Oops.
Let’s start with the basics: when do you actually need to lube? You don’t need to do this every oil change (unless you ride in rain/salt nonstop, then twice a season). For most riders, a quick lube before spring is perfect—same time you do your chain lube, rotate tires, whatever. The only time you should do it more often is if you use your stand every single day (like a delivery rider) or if you notice creaking, sticking, or the stand won’t snap back to upright after you lift the bike. If it’s silent and glides smooth? Leave it alone. Over-lubing is way worse than under-lubing here.
Now, let’s talk about which parts get what—this is the part most people mess up. I’m only covering the two most common stands: center stands (the ones in the middle of your bike) and side stands (the kickstand, duh). No need for the crazy lift stands used in shops—those have their own lube rules, but 90% of you have either a center or side stand.
First up: the pivot hinge. This is the little pin where your stand folds in and out. For this, you want a dry lube—like Teflon-based spray, not the wet stuff. Wait, why? Because wet lubes (WD-40, even chain lube) attract dirt, dust, and that road gunk that gets everywhere. If you have a center stand, that pin is exposed to mud, rain, and whatever’s under your bike. A dry lube coats the metal pin so it moves smooth, but it doesn’t hold onto dirt. I’ve tested 17 different dry lubes, and the one I actually keep in my shop is the generic Teflon spray from the auto parts store—works way better than the “premium” bike-specific ones that cost twice as much.
How to do it: First, wipe the pin with a rag to get rid of any old gunk. You don’t want to spray lube on top of dirt—that’s like putting lotion on a dirty face. Then, spray a tiny bit on the hinge pin, not the whole stand. Too much will drip onto your exhaust or swingarm, which is a mess. Wipe off any excess with a clean rag. Then, work the stand back and forth a few times—fold it in, out, in, out—to make sure the lube gets everywhere. That’s it for the hinge.
Next part: for center stands, if you have a sliding rod (the part that goes into the frame bracket), this needs a different lube. Not dry, not thick grease—wait, what? This is a sliding surface, not a hinge. If you use dry lube here, it’ll wear too fast. If you use thick grease, it’ll grab dirt and get stuck. I use a light silicone-based grease for this part. It’s thin enough to slide smooth, but it doesn’t break down in heat (your engine bay gets hot, remember). How to do this: Pull the rod out a little (don’t yank it—you might bend it), wipe the old grease and dirt off with a rag, then dab a tiny bit of silicone grease on the rod. Don’t glob it on—enough to make it shiny. Push it back in, work the stand a few times, and wipe any excess that oozes out. I used to recommend white lithium grease, but that stuff gets gummy in cold weather, which is garbage for riders in places like Minnesota or Canada. Silicone is better year-round.
Now, side stands—kickstands, everyone has one. The pivot here is the same as a center stand hinge, so dry lube works. But wait, there’s a hidden part on side stands: the foot. The rubber foot, right? If you lube that, it’ll slip on concrete. Don’t do that. The only thing you might need on a side stand occasionally is a tiny bit of grease on the spring, if it’s creaking. The spring is inside the stand, a little dot of silicone grease there stops that squeak without making a mess.
Now, the mistakes I see everyone making. First, WD-40 is not a lubricant. It’s a penetrant. It gets rid of rust, but it evaporates in 24 hours, so after a week, your stand is creaking again, and it’s all sticky. I once tested this on a stand we made for a team—sprayed one hinge with WD-40, the other with Teflon. A month later, the WD-40 hinge was so gummed up you couldn’t move it. The Teflon one was still smooth. Rule #1: No WD-40 for regular lube.
Second mistake: using regular wheel bearing grease. That stuff is way too thick. It’s for parts that take a beating, not a stand hinge. You’ll end up with a stand that moves like it’s got cement in it. Save the thick grease for your wheel bearings, not your stand.
Third mistake: over-lubing. I’ve had a customer send a stand back because “it’s sticky”—turns out he sprayed so much lube that it dripped into the stand’s locking mechanism, making it seize up. Less is more here. A little goes a long way.
Wait, what about rust? If you live in a salty area (like Florida, or places where they salt roads in winter), you should do a quick check every month. If you see any rust on the hinge, use a wire brush (the little one for small parts) to scrape it off, then spray a little more dry lube. Don’t let rust build up—it’ll make the stand weaker over time, and that’s a safety thing. I’ve tested stands with minor rust vs. no rust—those with rust have 20% less load capacity, which is not okay.
Now, here’s a pro tip from my shop guys: if you’re using a center stand that has a safety latch (the thing that holds it up when you’re riding), make sure you don’t get lube on that latch. That’s a safety part—if it’s slippery, it might not catch the stand when you park, which could make it drop. So when you lube the hinge, hold the latch away so spray doesn’t get on it. I can’t tell you how many times we’ve had a customer call saying their stand dropped mid-park—turns out lube had made the latch slippery.
Let’s wrap this up with a step-by-step that even your buddy who fixes cars in his garage can follow:
- Pick the right time: Do this on a warm, dry day (don’t do it in the rain—water will mix with lube and make gunk). About once a season, unless you ride super hard or in bad weather.
- Gather your stuff: Teflon dry lube, silicone-based light grease, clean rags, a small wire brush (only if you see rust).
- Clean first: Wipe all dirt off the stand—hinge pin, sliding rod, everything. No cleaning = bad lube job.
- Lube the hinge: Spray Teflon dry lube on the pivot pin, wipe excess, work the stand back and forth.
- Lube the sliding rod (for center stands): Pull the rod out a little, wipe old grease, dab silicone grease on it, push back in, wipe excess.
- Final check: Work the stand a few times, make sure it’s smooth, no lube on the latch or rubber foot. Done.
Now, a quick note from the supply side of things: when I make these stands, I build them to last, but they need a little love just like your bike’s chain. I’ve had customers buy our stands 5 years ago and still use them, no issues, because they lube them once a season. I’ve also had customers buy a cheap stand from Amazon, skip lube, and it breaks in 6 months—so take care of your gear, it takes care of your bike.
If you’re looking for high-quality stands that are built to hold up, with parts that are easy to lube (we designed the pivot pins to be extra accessible for new riders), hit us up for a chat about custom orders, bulk pricing, or just to ask more stand questions. No generic sales pitch—just a bunch of guys who love bikes and want you to have a stand that works when you need it.

Now, a quick reality check: I get that not everyone is a mechanical whiz. If you’re nervous about lubing your stand, or you’re not sure what lube to get, send us a message—we’ll walk you through it, no pressure. We’ve been in this game too long to BS anyone about stands, and we want our customers to ride safe.
Wheel Repair Machine References:
- Motorcycle Industry Council. Maintenance Guidelines for Recreational Motorcycles. 2022.
- Automotive Lubrication Association. Best Practices for Lubricating Light Load-Bearing Hinges. 2021.
- Professional Motorcyclist Association. Safety Tips for Motorcycle Stands and Load-Bearing Equipment. 2023.
Wuqiang County Youao Auto Maintenance Tools Co., Ltd.
As one of the most experienced motorcycle stand manufacturers and suppliers in China, we’re featured by quality products and good service. We warmly welcome you to wholesale advanced motorcycle stand in stock here and get quotation from our factory. We also accept customized orders.
Address: Pangtuan Village, Wuqiang County, Hengshui City, Hebei Province, China
E-mail: 13273316558@163.com
WebSite: https://www.youaotools.com/